HTCondor has two independent priority controls: job priorities and user priorities.
Job priorities allow a user to assign a priority level to each of their own submitted HTCondor jobs, in order to control the order of job execution. This handles the situation in which a user has more jobs queued, waiting to be executed, than there are machines available. Setting a job priority identifies the ordering in which that user's jobs are executed; a higher job priority job is matched and executed before a lower priority job. A job priority can be any integer, and larger values are of higher priority. So, 0 is a higher job priority than -3, and 6 is a higher job priority than 5.
For the simple case, each job can be given a distinct priority. For an already queued job, its priority may be set with the condor_prio command; see the example in section 2.6.4, or the condor_prio manual page for details. This sets the value of job ClassAd attribute JobPrio.
A fine-grained categorization of jobs and their ordering is available for experts by using the job ClassAd attributes: PreJobPrio1, PreJobPrio2, JobPrio, PostJobPrio1, or PostJobPrio2.
Machines are allocated to users based upon a user's priority. A lower numerical value for user priority means higher priority, so a user with priority 5 will get more resources than a user with priority 50. User priorities in HTCondor can be examined with the condor_userprio command (see page ). HTCondor administrators can set and change individual user priorities with the same utility.
HTCondor continuously calculates the share of available machines that each user should be allocated. This share is inversely related to the ratio between user priorities. For example, a user with a priority of 10 will get twice as many machines as a user with a priority of 20. The priority of each individual user changes according to the number of resources the individual is using. Each user starts out with the best possible priority: 0.5. If the number of machines a user currently has is greater than the user priority, the user priority will worsen by numerically increasing over time. If the number of machines is less then the priority, the priority will improve by numerically decreasing over time. The long-term result is fair-share access across all users. The speed at which HTCondor adjusts the priorities is controlled with the configuration variable PRIORITY_HALFLIFE, an exponential half-life value. The default is one day. If a user that has user priority of 100 and is utilizing 100 machines removes all his/her jobs, one day later that user's priority will be 50, and two days later the priority will be 25.
HTCondor enforces that each user gets his/her fair share of machines according to user priority both when allocating machines which become available and by priority preemption of currently allocated machines. For instance, if a low priority user is utilizing all available machines and suddenly a higher priority user submits jobs, HTCondor will immediately take a checkpoint and vacate jobs belonging to the lower priority user. This will free up machines that HTCondor will then give over to the higher priority user. HTCondor will not starve the lower priority user; it will preempt only enough jobs so that the higher priority user's fair share can be realized (based upon the ratio between user priorities). To prevent thrashing of the system due to priority preemption, the HTCondor site administrator can define a PREEMPTION_REQUIREMENTS expression in HTCondor's configuration. The default expression that ships with HTCondor is configured to only preempt lower priority jobs that have run for at least one hour. So in the previous example, in the worse case it could take up to a maximum of one hour until the higher priority user receives a fair share of machines. For a general discussion of limiting preemption, please see section of the Administrator's manual.
User priorities are keyed on <username>@<domain>, for example firstname.lastname@example.org. The domain name to use, if any, is configured by the HTCondor site administrator. Thus, user priority and therefore resource allocation is not impacted by which machine the user submits from or even if the user submits jobs from multiple machines.
An extra feature is the ability to submit a job as a nice job (see page ). Nice jobs artificially boost the user priority by ten million just for the nice job. This effectively means that nice jobs will only run on machines that no other HTCondor job (that is, non-niced job) wants. In a similar fashion, an HTCondor administrator could set the user priority of any specific HTCondor user very high. If done, for example, with a guest account, the guest could only use cycles not wanted by other users of the system.
When HTCondor needs a job to vacate a machine for whatever reason, it sends the job an asynchronous signal specified in the KillSig attribute of the job's ClassAd. The value of this attribute can be specified by the user at submit time by placing the kill_sig option in the HTCondor submit description file.
If a program wanted to do some special work when required to vacate a machine, the program may set up a signal handler to use a trappable signal as an indication to clean up. When submitting this job, this clean up signal is specified to be used with kill_sig. Note that the clean up work needs to be quick. If the job takes too long to go away, HTCondor follows up with a SIGKILL signal which immediately terminates the process.
A job that is linked using condor_compile and is subsequently submitted into the standard universe, will checkpoint and exit upon receipt of a SIGTSTP signal. Thus, SIGTSTP is the default value for KillSig when submitting to the standard universe. The user's code may still checkpoint itself at any time by calling one of the following functions exported by the HTCondor libraries:
For jobs submitted into the vanilla universe, the default value for KillSig is SIGTERM, the usual method to nicely terminate a Unix program.