This section on network communication in HTCondor discusses which network ports are used, how HTCondor behaves on machines with multiple network interfaces and IP addresses, and how to facilitate functionality in a pool that spans firewalls and private networks.
The security section of the manual contains some information that is relevant to the discussion of network communication which will not be duplicated here, so please see section 3.6 as well.
Firewalls, private networks, and network address translation (NAT) pose special problems for HTCondor. There are currently two main mechanisms for dealing with firewalls within HTCondor:
Each method has its own advantages and disadvantages, as described below.
These parameters and values are URL-encoded. This means any special character is encoded with %, followed by two hexadecimal digits specifying the ASCII value. Special characters are any non-alphanumeric character.
HTCondor currently recognizes the following parameters with an IPv4 port specification:
IP:port#ID. Note that spaces between list items will be URL encoded by
Every HTCondor daemon listens on a network port for incoming commands. (Using condor_shared_port, this port may be shared between multiple daemons.) Most daemons listen on a dynamically assigned port. In order to send a message, HTCondor daemons and tools locate the correct port to use by querying the condor_collector, extracting the port number from the ClassAd. One of the attributes included in every daemon's ClassAd is the full IP address and port number upon which the daemon is listening.
To access the condor_collector itself, all HTCondor daemons and tools must know the port number where the condor_collector is listening. The condor_collector is the only daemon with a well-known, fixed port. By default, HTCondor uses port 9618 for the condor_collector daemon. However, this port number can be changed (see below).
As an optimization for daemons and tools communicating with another daemon that is running on the same host, each HTCondor daemon can be configured to write its IP address and port number into a well-known file. The file names are controlled using the <SUBSYS>_ADDRESS_FILE configuration variables, as described in section 3.3.4 on page .
NOTE: In the 6.6 stable series, and HTCondor versions earlier than 6.7.5, the condor_negotiator also listened on a fixed, well-known port (the default was 9614). However, beginning with version 6.7.5, the condor_negotiator behaves like all other HTCondor daemons, and publishes its own ClassAd to the condor_collector which includes the dynamically assigned port the condor_negotiator is listening on. All HTCondor tools and daemons that need to communicate with the condor_negotiator will either use the NEGOTIATOR_ADDRESS_FILE or will query the condor_collector for the condor_negotiator's ClassAd.
Sites that configure any checkpoint servers will introduce other fixed ports into their network. Each condor_ckpt_server will listen to 4 fixed ports: 5651, 5652, 5653, and 5654. There is currently no way to configure alternative values for any of these ports.
CONDOR_HOST = machX.cs.wisc.edu COLLECTOR_HOST = $(CONDOR_HOST)the configuration might be
CONDOR_HOST = machX.cs.wisc.edu COLLECTOR_HOST = $(CONDOR_HOST):9650
If a non standard port is defined, the same value of COLLECTOR_HOST (including the port) must be used for all machines in the HTCondor pool. Therefore, this setting should be modified in the global configuration file (condor_config file), or the value must be duplicated across all configuration files in the pool if a single configuration file is not being shared.
When querying the condor_collector for a remote pool that is running on a non standard port, any HTCondor tool that accepts the -pool argument can optionally be given a port number. For example:
% condor_status -pool foo.bar.org:1234
On single machine pools, it is permitted to configure the condor_collector daemon to use a dynamically assigned port, as given out by the operating system. This prevents port conflicts with other services on the same machine. However, a dynamically assigned port is only to be used on single machine HTCondor pools, and only if the COLLECTOR_ADDRESS_FILE configuration variable has also been defined. This mechanism allows all of the HTCondor daemons and tools running on the same machine to find the port upon which the condor_collector daemon is listening, even when this port is not defined in the configuration file and is not known in advance.
To enable the condor_collector daemon to use a dynamically assigned port, the port number is set to 0 in the COLLECTOR_HOST variable. The COLLECTOR_ADDRESS_FILE configuration variable must also be defined, as it provides a known file where the IP address and port information will be stored. All HTCondor clients know to look at the information stored in this file. For example:
COLLECTOR_HOST = $(CONDOR_HOST):0 COLLECTOR_ADDRESS_FILE = $(LOG)/.collector_address
Configuration definition of COLLECTOR_ADDRESS_FILE is in section 3.3.4 on page , and COLLECTOR_HOST is in section 3.3.2 on page .
If an HTCondor pool is completely behind a firewall, then no special consideration or port usage is needed. However, if there is a firewall between the machines within an HTCondor pool, then configuration variables may be set to force the usage of specific ports, and to utilize a specific range of ports.
By default, HTCondor uses port 9618 for the condor_collector daemon, and dynamic (apparently random) ports for everything else. See section 3.7.1, if a dynamically assigned port is desired for the condor_collector daemon.
All of the HTCondor daemons on a machine may be configured to share a single port. See section 3.3.32 for more information.
The configuration variables HIGHPORT and LOWPORT facilitate setting a restricted range of ports that HTCondor will use. This may be useful when some machines are behind a firewall. The configuration macros HIGHPORT and LOWPORT will restrict dynamic ports to the range specified. The configuration variables are fully defined in section 3.3.5. All of these ports must be greater than 0 and less than 65,536. Note that both HIGHPORT and LOWPORT must be at least 1024 for HTCondor version 6.6.8. In general, use ports greater than 1024, in order to avoid port conflicts with standard services on the machine. Another reason for using ports greater than 1024 is that daemons and tools are often not run as root, and only root may listen to a port lower than 1024. Also, the range must include enough ports that are not in use, or HTCondor cannot work.
The range of ports assigned may be restricted based on incoming (listening) and outgoing (connect) ports with the configuration variables IN_HIGHPORT, IN_LOWPORT, OUT_HIGHPORT, and OUT_LOWPORT. See section 3.3.5 for complete definitions of these configuration variables. A range of ports lower than 1024 for daemons running as root is appropriate for incoming ports, but not for outgoing ports. The use of ports below 1024 (versus above 1024) has security implications; therefore, it is inappropriate to assign a range that crosses the 1024 boundary.
NOTE: Setting HIGHPORT and LOWPORT will not automatically force the condor_collector to bind to a port within the range. The only way to control what port the condor_collector uses is by setting the COLLECTOR_HOST (as described above).
The total number of ports needed depends on the size of the pool, the usage of the machines within the pool (which machines run which daemons), and the number of jobs that may execute at one time. Here we discuss how many ports are used by each participant in the system. This assumes that condor_shared_port is not being used. If it is being used, then all daemons can share a single incoming port.
The central manager of the pool needs 5 + NEGOTIATOR_SOCKET_CACHE_SIZE ports for daemon communication, where NEGOTIATOR_SOCKET_CACHE_SIZE is specified in the configuration or defaults to the value 16.
Each execute machine (those machines running a condor_startd daemon) requires 5 + (5 * number of slots advertised by that machine) ports. By default, the number of slots advertised will equal the number of physical CPUs in that machine.
Submit machines (those machines running a condor_schedd daemon) require 5 + (5 * MAX_JOBS_RUNNING) ports. The configuration variable MAX_JOBS_RUNNING limits (on a per-machine basis, if desired) the maximum number of jobs. Without this configuration macro, the maximum number of jobs that could be simultaneously executing at one time is a function of the number of reachable execute machines.
Also be aware that HIGHPORT and LOWPORT only impact dynamic port selection used by the HTCondor system, and they do not impact port selection used by jobs submitted to HTCondor. Thus, jobs submitted to HTCondor that may create network connections may not work in a port restricted environment. For this reason, specifying HIGHPORT and LOWPORT is not going to produce the expected results if a user submits MPI applications to be executed under the parallel universe.
Where desired, a local configuration for machines not behind a firewall can override the usage of HIGHPORT and LOWPORT, such that the ports used for these machines are not restricted. This can be accomplished by adding the following to the local configuration file of those machines not behind a firewall:
HIGHPORT = UNDEFINED LOWPORT = UNDEFINED
If the maximum number of ports allocated using HIGHPORT and LOWPORT is too few, socket binding errors of the form
failed to bind any port within <$LOWPORT> - <$HIGHPORT>are likely to appear repeatedly in log files.
The condor_shared_port is an optional daemon responsible for creating a TCP listener port shared by all of the HTCondor daemons.
The main purpose of the condor_shared_port daemon is to reduce the number of ports that must be opened. This is desirable when HTCondor daemons need to be accessible through a firewall. This has a greater security benefit than simply reducing the number of open ports. Without the condor_shared_port daemon, HTCondor can use a range of ports, but since some HTCondor daemons are created dynamically, this full range of ports will not be in use by HTCondor at all times. This implies that other non-HTCondor processes not intended to be exposed to the outside network could unintentionally bind to ports in the range intended for HTCondor, unless additional steps are taken to control access to those ports. While the condor_shared_port daemon is running, it is exclusively bound to its port, which means that other non-HTCondor processes cannot accidentally bind to that port.
A second benefit of the condor_shared_port daemon is that it helps address the scalability issues of a submit machine. Without the condor_shared_port daemon, more than 2 ephemeral ports per running job are often required, depending on the rate of job completion. There are only 64K ports in total, and most standard Unix installations only allocate a subset of these as ephemeral ports. Therefore, with long running jobs, and with between 11K and 14K simultaneously running jobs, port exhaustion has been observed in typical Linux installations. After increasing the ephemeral port range to its maximum, port exhaustion occurred between 20K and 25K running jobs. Using the condor_shared_port daemon dramatically reduces the required number of ephemeral ports on the submit node where the submit node connects directly to the execute node. If the submit node connects via CCB to the execute node, no ports are required per running job; only the one port allocated to the condor_shared_port daemon is used.
When CCB is enabled, the condor_shared_port daemon registers with the CCB server on behalf of all daemons sharing the port. This means that it is not possible to individually enable or disable CCB connectivity to daemons that are using the shared port; they all effectively share the same setting, and the condor_shared_port daemon handles all CCB connection requests on their behalf.
HTCondor's authentication and authorization steps are unchanged by the use of a shared port. Each HTCondor daemon continues to operate according to its configured policy. Requests for connections to the shared port are not authenticated or restricted by the condor_shared_port daemon. They are simply passed to the requested daemon, which is then responsible for enforcing the security policy.
When the condor_master is configured to use the shared port by setting the configuration variable
USE_SHARED_PORT = Truethe condor_shared_port daemon is treated specially. SHARED_PORT is automatically added to DAEMON_LIST. A command such as condor_off, which shuts down all daemons except for the condor_master, will also leave the condor_shared_port running. This prevents the condor_master from getting into a state where it can no longer receive commands.
Also when USE_SHARED_PORT = True, the condor_collector needs to be configured to use a shared port, so that connections to the shared port that are destined for the condor_collector can be forwarded. As an example, the shared port socket name of the condor_collector with shared port number 11000 is
COLLECTOR_HOST = cm.host.name:11000?sock=collector
This example assumes that the socket name used by the condor_collector is collector, and it runs on cm.host.name. This configuration causes the condor_collector to automatically choose this socket name. If multiple condor_collector daemons are started on the same machine, the socket name can be explicitly set in the daemon's invocation arguments, as in the example:
COLLECTOR_ARGS = -sock collector
When the condor_collector address is a shared port, TCP updates will be automatically used instead of UDP, because the condor_shared_port daemon does not work with UDP messages. Under Unix, this means that the condor_collector daemon should be configured to have enough file descriptors. See section 3.7.5 for more information on using TCP within HTCondor.
SOAP commands cannot be sent through the condor_shared_port daemon.
However, a daemon may be configured to open a fixed, non-shared port,
in addition to using a shared port.
This is done both by setting
USE_SHARED_PORT = True and by specifying a fixed port for the daemon
<SUBSYS>_ARGS = -p <portnum>.
The TCP connections required to manage standard universe jobs do not make use of shared ports. Therefore, if the firewall is configured to only allow connections through the shared port, standard universe jobs will not be able to run.
HTCondor can run on machines with multiple network interfaces. Starting with HTCondor version 6.7.13 (and therefore all HTCondor 6.8 and more recent versions), new functionality is available that allows even better support for multi-homed machines, using the configuration variable BIND_ALL_INTERFACES. A multi-homed machine is one that has more than one NIC (Network Interface Card). Further improvements to this new functionality will remove the need for any special configuration in the common case. For now, care must still be given to machines with multiple NICs, even when using this new configuration variable.
Machines can be configured such that whenever HTCondor daemons or tools call bind(), the daemons or tools use all network interfaces on the machine. This means that outbound connections will always use the appropriate network interface to connect to a remote host, instead of being forced to use an interface that might not have a route to the given destination. Furthermore, sockets upon which a daemon listens for incoming connections will be bound to all network interfaces on the machine. This means that so long as remote clients know the right port, they can use any IP address on the machine and still contact a given HTCondor daemon.
This functionality is on by default. To disable this functionality, the boolean configuration variable BIND_ALL_INTERFACES is defined and set to False:
BIND_ALL_INTERFACES = FALSE
This functionality has limitations. Here are descriptions of the limitations.
Currently, HTCondor daemons can only advertise two IP addresses in the ClassAd they send to their condor_collector. One is the public IP address and the other is the private IP address. HTCondor tools and other daemons that wish to connect to the daemon will use the private IP address if they are configured with the same private network name, and they will use the public IP address otherwise. So, even if the daemon is listening on 3 or more different interfaces, each with a separate IP, the daemon must choose which two IP addresses to advertise so that other daemons and tools can connect to it.
By default, HTCondor advertises the IP address of the network interface used to contact the condor_collector as its public address, since this is the most likely to be accessible to other processes that query the same condor_collector. The NETWORK_INTERFACE configuration variable can be used to specify the public IP address HTCondor should advertise, and PRIVATE_NETWORK_INTERFACE, along with PRIVATE_NETWORK_NAME can be used to specify the private IP address to advertise.
Sites that make heavy use of private networks and multi-homed machines should consider if using the HTCondor Connection Broker, CCB, is right for them. More information about CCB and HTCondor can be found in section 3.7.4 on page .
Often users of HTCondor wish to set up compute farms where there is one machine with two network interface cards (one for the public Internet, and one for the private net). It is convenient to set up the head node as a central manager in most cases and so here are the instructions required to do so.
Setting up the central manager on a machine with more than one NIC can be a little confusing because there are a few external variables that could make the process difficult. One of the biggest mistakes in getting this to work is that either one of the separate interfaces is not active, or the host/domain names associated with the interfaces are incorrectly configured.
Given that the interfaces are up and functioning, and they have good host/domain names associated with them here is how to configure HTCondor:
In this example, farm-server.farm.org maps to the private interface. In the central manager's global (to the cluster) configuration file:
CONDOR_HOST = farm-server.farm.org
In the central manager's local configuration file:
NETWORK_INTERFACE = <IP address of farm-server.farm.org> NEGOTIATOR = $(SBIN)/condor_negotiator COLLECTOR = $(SBIN)/condor_collector DAEMON_LIST = MASTER, COLLECTOR, NEGOTIATOR, SCHEDD, STARTD
If the central manager and farm machines are all NT, then only vanilla universe will work now. However, if this is set up for Unix, then at this point, standard universe jobs should be able to function in the pool. But, if UID_DOMAIN is not configured to be homogeneous across the farm machines, the standard universe jobs will run as nobody on the farm machines.
In order to get vanilla jobs and file server load balancing for standard universe jobs working (under Unix), do some more work both in the cluster you have put together and in HTCondor to make everything work. First, you need a file server (which could also be the central manager) to serve files to all of the farm machines. This could be NFS or AFS, and it does not really matter to HTCondor. The mount point of the directories you wish your users to use must be the same across all of the farm machines. Now, configure UID_DOMAIN and FILESYSTEM_DOMAIN to be homogeneous across the farm machines and the central manager. Inform HTCondor that an NFS or AFS file system exists and that is done in this manner. In the global (to the farm) configuration file:
# If you have NFS USE_NFS = True # If you have AFS HAS_AFS = True USE_AFS = True # if you want both NFS and AFS, then enable both sets above
Now, if the cluster is set up so that it is possible for a machine name to never have a domain name (for example, there is machine name but no fully qualified domain name in /etc/hosts), configure DEFAULT_DOMAIN_NAME to be the domain that is to be added on to the end of the host name.
If client machine has two or more NICs, then there might be a specific network interface on which the client machine desires to communicate with the rest of the HTCondor pool. In this case, the local configuration file for the client should have
NETWORK_INTERFACE = <IP address of desired interface>
If a checkpoint server is on a machine with multiple interfaces, then 2 items must be correct to get things to work:
HTCondor Connection Brokering, or CCB, is a way of allowing HTCondor components to communicate with each other when one side is in a private network or behind a firewall. Specifically, CCB allows communication across a private network boundary in the following scenario: an HTCondor tool or daemon (process A) needs to connect to an HTCondor daemon (process B), but the network does not allow a TCP connection to be created from A to B; it only allows connections from B to A. In this case, B may be configured to register itself with a CCB server that both A and B can connect to. Then when A needs to connect to B, it can send a request to the CCB server, which will instruct B to connect to A so that the two can communicate.
As an example, consider an HTCondor execute node that is within a private network. This execute node's condor_startd is process B. This execute node cannot normally run jobs submitted from a machine that is outside of that private network, because bi-directional connectivity between the submit node and the execute node is normally required. However, if both execute and submit machine can connect to the CCB server, if both are authorized by the CCB server, and if it is possible for the execute node within the private network to connect to the submit node, then it is possible for the submit node to run jobs on the execute node.
To effect this CCB solution, the execute node's condor_startd within the private network registers itself with the CCB server by setting the configuration variable CCB_ADDRESS. The submit node's condor_schedd communicates with the CCB server, requesting that the execute node's condor_startd open the TCP connection. The CCB server forwards this request to the execute node's condor_startd, which opens the TCP connection. Once the connection is open, bi-directional communication is enabled.
If the location of the execute and submit nodes is reversed with respect to the private network, the same idea applies: the submit node within the private network registers itself with a CCB server, such that when a job is running and the execute node needs to connect back to the submit node (for example, to transfer output files), the execute node can connect by going through CCB to request a connection.
If both A and B are in separate private networks, then CCB alone cannot provide connectivity. However, if an incoming port or port range can be opened in one of the private networks, then the situation becomes equivalent to one of the scenarios described above and CCB can provide bi-directional communication given only one-directional connectivity. See section for information on opening port ranges. Also note that CCB works nicely with condor_shared_port.
Unfortunately at this time, CCB does not support standard universe jobs.
Any condor_collector may be used as a CCB server. There is no requirement that the condor_collector acting as the CCB server be the same condor_collector that a daemon advertises itself to (as with COLLECTOR_HOST). However, this is often a convenient choice.
This example assumes that there is a pool of machines in a private network that need to be made accessible from the outside, and that the condor_collector (and therefore CCB server) used by these machines is accessible from the outside. Accessibility might be achieved by a special firewall rule for the condor_collector port, or by being on a dual-homed machine in both networks.
The configuration of variable CCB_ADDRESS on machines in the private network causes registration with the CCB server as in the example:
CCB_ADDRESS = $(COLLECTOR_HOST) PRIVATE_NETWORK_NAME = cs.wisc.edu
The definition of PRIVATE_NETWORK_NAME ensures that all communication between nodes within the private network continues to happen as normal, and without going through the CCB server. The name chosen for PRIVATE_NETWORK_NAME should be different from the private network name chosen for any HTCondor installations that will be communicating with this pool.
Under Unix, and with large HTCondor pools, it is also necessary to give the condor_collector acting as the CCB server a large enough limit of file descriptors. This may be accomplished with the configuration variable MAX_FILE_DESCRIPTORS or an equivalent. Each HTCondor process configured to use CCB with CCB_ADDRESS requires one persistent TCP connection to the CCB server. A typical execute node requires one connection for the condor_master, one for the condor_startd, and one for each running job, as represented by a condor_starter. A typical submit machine requires one connection for the condor_master, one for the condor_schedd, and one for each running job, as represented by a condor_shadow. If there will be no administrative commands required to be sent to the condor_master from outside of the private network, then CCB may be disabled in the condor_master by assigning MASTER.CCB_ADDRESS to nothing:
Completing the count of TCP connections in this example: suppose the pool consists of 500 8-slot execute nodes and CCB is not disabled in the configuration of the condor_master processes. In this case, the count of needed file descriptors plus some extra for other transient connections to the collector is 500*(1+1+8)=5000. Be generous, and give it twice as many descriptors as needed by CCB alone:
COLLECTOR.MAX_FILE_DESCRIPTORS = 10000
The CCB server authorizes all daemons that register themselves with it (using CCB_ADDRESS) at the DAEMON authorization level (these are playing the role of process A in the above description). It authorizes all connection requests (from process B) at the READ authorization level. As usual, whether process B authorizes process A to do whatever it is trying to do is up to the security policy for process B; from the HTCondor security model's point of view, it is as if process A connected to process B, even though at the network layer, the reverse is true.
Errors registering with CCB or requesting connections via CCB are logged at level D_ALWAYS in the debugging log. These errors may be identified by searching for "CCB" in the log message. Command-line tools require the argument -debug for this information to be visible. To see details of the CCB protocol add D_FULLDEBUG to the debugging options for the particular HTCondor subsystem of interest. Or, add D_FULLDEBUG to ALL_DEBUG to get extra debugging from all HTCondor components.
A daemon that has successfully registered itself with CCB will advertise this fact in its address in its ClassAd. The ClassAd attribute MyAddress will contain information about its "CCBID".
Any number of CCB servers may be used to serve a pool of HTCondor daemons. For example, half of the pool could use one CCB server and half could use another. Or for redundancy, all daemons could use both CCB servers and then CCB connection requests will load-balance across them. Typically, the limit of how many daemons may be registered with a single CCB server depends on the authentication method used by the condor_collector for DAEMON-level and READ-level access, and on the amount of memory available to the CCB server. We are not able to provide specific recommendations at this time, but to give a very rough idea, a server class machine should be able to handle CCB service plus normal condor_collector service for a pool containing a few thousand slots without much trouble.
TCP sockets are reliable, connection-based sockets that guarantee the delivery of any data sent. However, TCP sockets are fairly expensive to establish, and there is more network overhead involved in sending and receiving messages.
UDP sockets are datagrams, and are not reliable. There is very little overhead in establishing or using a UDP socket, but there is also no guarantee that the data will be delivered. The lack of guaranteed delivery of UDP will negatively affect some pools, particularly ones comprised of machines across a wide area network (WAN) or highly-congested network links, where UDP packets are frequently dropped.
By default, HTCondor daemons will use TCP to send updates to the condor_collector, with the exception of the condor_collector forwarding updates to any condor_collector daemons specified in CONDOR_VIEW_HOST, where UDP is used. These configuration variables control the protocol used:
When there are sufficient file descriptors, the condor_collector leaves established TCP sockets open, facilitating better performance. Subsequent updates can reuse an already open socket.
Each HTCondor daemon that sends updates to the condor_collector will have 1 socket open to it. So, in a pool with N machines, each of them running a condor_master, condor_schedd, and condor_startd, the condor_collector would need at least 3*N file descriptors. If the condor_collector is also acting as a CCB server, it will require an additional file descriptor for each registered daemon. In the default configuration, the number of file descriptors available to the condor_collector is 10240. For very large pools, the number of descriptor can be modified with the configuration:
COLLECTOR_MAX_FILE_DESCRIPTORS = 40960
If there are insufficient file descriptors for all of the daemons sending updates to the condor_collector, a warning will be printed in the condor_collector log file. The string "file descriptor safety level exceeded" identifies this warning.
HTCondor supports using IPv4, IPv6, or both. By default, HTCondor will look at a machine's interfaces, and on that machine, enable each protocol for which it finds at least one interface with an address of that procol.
To require IPv4, you may set ENABLE_IPV4 to true; if the machine does not have an interface with an IPv4 address, HTCondor will not start. Likewise, to require IPv6, you may set ENABLE_IPV6 to true.
If you set ENABLE_IPV4 to false, HTCondor will not use IPv4, even if it is available; likewise for ENABLE_IPV6 and IPv6.
The default setting for ENABLE_IPV4 and ENABLE_IPV6 is auto, which uses the corresponding protocol if and only HTCondor finds an interface with an address of that protocol.
If both IPv4 and IPv6 networking are enabled, HTCondor runs in mixed mode. In mixed mode, HTCondor daemons have at least one IPv4 address and at least one IPv6 address. Other daemons and the command-line tools choose between these addresses based on which protocols are enabled for them; if both are, they will prefer the first address listed by that daemon.
A daemon may be listening on one, some, or all of its machine's addresses. (See NETWORK_INTERFACE.) Daemons may presently list at most two addresses, one IPv6 and one IPv4. Each address is the ``most public'' address of its protocol; by default, the IPv6 address is listed first. HTCondor selects the ``most public'' address heuristically.
Nonetheless, there are two cases in which HTCondor may not use an IPv6 address when one is available:
You may force HTCondor to prefer IPv4 in all three of these situations by setting the macro PREFER_IPV4 to true; this is the default. With PREFER_IPV4 set, HTCondor daemons will list their ``most public'' IPv4 address first; prefer the IPv4 address when choosing from another's daemon list; and prefer the IPv4 address when looking up a host name in DNS.
In practice, both an HTCondor pool's central manager and any submit machines within a mixed mode pool must have both IPv4 and IPv6 addresses for both IPv4-only and IPv6-only condor_startd daemons to function properly.
You may freely intermix IPv6 and IPv4 address literals. You may also specify IPv6 netmasks as a legal IPv6 address followed by a slash followed by the number of bits in the mask; or as the prefix of a legal IPv6 address followed by two colons followed by an asterisk. The latter is entirely equivalent to the former, except that it only allows you to (implicitly) specify mask bits in groups of sixteen. For example, fe8f:1234::/60 and fe8f:1234::* specify the same network mask.
The HTCondor security subsystem resolves names in the ALLOW and DENY lists and uses all of the resulting IP addresses. Thus, to allow or deny IPv6 addresses, the names must have IPv6 DNS entries (AAAA records), or NO_DNS must be enabled.
When you specify an IPv6 address and a port number simultaneously, you must separate the IPv6 address from the port number by placing square brackets around the address. For instance:
COLLECTOR_HOST = [2607:f388:1086:0:21e:68ff:fe0f:6462]:5332
If you do not (or may not) specify a port, do not use the square brackets. For instance:
NETWORK_INTERFACE = 1234:5678::90ab
When using the configuration variable NO_DNS, IPv6 addresses are turned into host names by taking the IPv6 address, changing colons to dashes, and appending $(DEFAULT_DOMAIN_NAME). So,